Форум программистов, компьютерный форум, киберфорум
Серверы и серверное железо
Войти
Регистрация
Восстановить пароль
 
Рейтинг 4.80/5: Рейтинг темы: голосов - 5, средняя оценка - 4.80
0 / 0 / 0
Регистрация: 10.10.2021
Сообщений: 3
1

Intel S5000PSL после замены несколько алертов в Health Status Esxi

10.10.2021, 20:56. Показов 866. Ответов 3
Метки нет (Все метки)

Добрый вечер, коллеги.

Есть материнская плата Intel S5000PSL (тоже б.у), которую отправили из другого филиала на замену аналогичной, неисправной материнской плате. Уточню, что старая материнская плата не совсем мертвая. Может стабильно проработать несколько часов и даже дней. И пока она работала, никаких ошибок в установленном esxi 6.0 на вкладке HealthStatus не наблюдалось.
Различие между двумя платами я заметил только одно: разные версии BIOS. На старой плате S5000.86B.10.00.0004, на новой же S5000.86B.15.00.0101
На старой плате стояло два одинаковых процессора Intel Xeon 5110, которые я установил на новую. Ну и все остальное тоже переставил. При запуске ESXI на вкладке HelthStatus появилось сразу несколько alert-ов:
Код
- Temperature - Processor 1 Proc 1 Temp - Alert - 127 degrees C 
- Power - Power Supply 2 PS2 Status 0: Config Error: Vendor Mismatch - Assert - Alert
- Power - Power Supply 1 PS1 Status 0: Config Error: Vendor Mismatch - Assert - Alert
Причем температура процессора не меняется ни на градус.
Что уже сделано:
- Поменял процессоры местами, но ничего не изменилось.
- Загрузился с live usb: использовал windows 10pe. Мониторил температуру Aida64
Температура обоих процессоров не поднималась выше 50 градусов.
- Предположил, что проблема в настройках биос. Перенес всё оборудование на старую материнку запустил - проверил настройки и убедился, что в esxi ошибок нет
- В интернете нашел информацию, что проблема может исчезнуть если почистить System Event Log в биос. Установил на флешку SEL Viewer загрузился в биос, там тоже выставил опцию Clear Event Log. Загрузил SEL Viewer и действительно увидел там старые ошибки. Почистил, перезагрузился. В esxi нажал reset sensors, но ничего не поменялось. Снова загрузился в SEL Viewer и снова увидел там ошибки только дата уже свежая, текущая.
- Засомневался и решил снова загрузиться с usb, на этот раз использовал ubuntu 16 и соответственно lm-sensors. И снова наблюдал температуру не выше 50 градусов.
Собственно вопрос: может что-то делаю не так, где-то ещё забыл почистить логи или все же проблема с оборудованием?
0
Programming
Эксперт
94731 / 64177 / 26122
Регистрация: 12.04.2006
Сообщений: 116,782
10.10.2021, 20:56
Ответы с готовыми решениями:

ST31000524AS Health Status 59% после 2700ч работы
У меня жесткий диск на 1тб, ST31000524AS. Смарт говорит, что он проработал 2768ч и состояние...

После замены с Intel Celeron D на Intel Core 2 Quad Q6700 загрузка компьютера наглухо зависает после определен
После замены с Intel Celeron D на Intel Core 2 Quad Q6700 загрузка компьютера наглухо зависает...

INTEL S5000PSL (SAS) пойдет с Xeon E5345?
Добрый день, кто может подсказать по поддержке процессоров на материнской плате INTEL...

Intel S5000PSL+2x Xeon 5150+8Gb DDR2 PC2-5300F
Вобщем, нужно работать паралельно на Debian и в Win7. Первая как основная система, Win7 на...

Не запускается Win10 после замены процессора Intel
Идём по порядку. На компе стоял Dual Core старенький e5200 в Gigabyte ga-p35-ds3, блок питания на...

3
0 / 0 / 0
Регистрация: 10.10.2021
Сообщений: 3
11.10.2021, 10:24  [ТС] 2
Также сохранил логи SEL Viewer-ом:
Код
1   	10/10/2021-08:15:00  	Event Log Cleared /System Event Log 	The BMC on S5000PSL has reported an informational assertion event for System Event Log.  The event has the following information: the log area has been reset and/or cleared.  There is no recommended action defined for this event.                                                                                                                                                                        	BMC - LUN #0 (Channel #00h)                   

2   	10/10/2021-08:15:42  	Temperature /Proc 1 Temp (#0x98)    	The BMC on S5000PSL has reported an informational deassertion event for Proc 1 Temp.  The event has the following information: the Proc 1 Temp is no longer in a high non-critical state.  Sensor reading: 127.00  degrees C.  Threshold value: 99.00  degrees C.  No action is required.                                                                                                                    	BMC - LUN #0 (Channel #00h)                   

3   	10/10/2021-08:15:42  	Temperature /Proc 1 Temp (#0x98)    	The BMC on S5000PSL has reported an informational deassertion event for Proc 1 Temp.  The event has the following information: the Proc 1 Temp is no longer in a critically high state.  Sensor reading: 127.00  degrees C.  Threshold value: 108.00  degrees C.  No action is required.                                                                                                                     	BMC - LUN #0 (Channel #00h)                   

4   	10/10/2021-08:15:43  	Temperature /Proc 1 Temp (#0x98)    	The BMC on S5000PSL has reported a warning assertion event for Proc 1 Temp.  The event has the following information: the Proc 1 Temp is in a high, but non-critical, and going higher state.  Sensor reading: 127.00  degrees C.  Threshold value: 99.00  degrees C.  Please check the device.                                                                                                              	BMC - LUN #0 (Channel #00h)                   

5   	10/10/2021-08:15:43  	Temperature /Proc 1 Temp (#0x98)    	The BMC on S5000PSL has reported a critical assertion event for Proc 1 Temp.  The event has the following information: the Proc 1 Temp is high, critical, and going higher state.  Sensor reading: 127.00  degrees C.  Threshold value: 108.00  degrees C.  Please check the device.                                                                                                                         	BMC - LUN #0 (Channel #00h)                   

6   	10/10/2021-08:16:12  	System Event #0x83                  	The BIOS on S5000PSL has reported an informational assertion event for System Event sensor 131.  The event has the following information: Timestamp Clock Sync. Event is first of the pair.  There is no recommended action defined for this event.                                                                                                                                                          	BIOS (Channel #00h)                           

7   	10/10/2021-08:16:13  	System Event #0x83                  	The BIOS on S5000PSL has reported an informational assertion event for System Event sensor 131.  The event has the following information: Timestamp Clock Sync. Event is second of the pair.  There is no recommended action defined for this event.                                                                                                                                                         	BIOS (Channel #00h)                           

8   	10/10/2021-08:17:17  	Temperature /Proc 1 Temp (#0x98)    	The BMC on S5000PSL has reported an informational deassertion event for Proc 1 Temp.  The event has the following information: the Proc 1 Temp is no longer in a high non-critical state.  Sensor reading: 127.00  degrees C.  Threshold value: 99.00  degrees C.  No action is required.                                                                                                                    	BMC - LUN #0 (Channel #00h)                   

9   	10/10/2021-08:17:17  	Temperature /Proc 1 Temp (#0x98)    	The BMC on S5000PSL has reported an informational deassertion event for Proc 1 Temp.  The event has the following information: the Proc 1 Temp is no longer in a critically high state.  Sensor reading: 127.00  degrees C.  Threshold value: 108.00  degrees C.  No action is required.                                                                                                                     	BMC - LUN #0 (Channel #00h)                   

10  	10/10/2021-08:17:17  	Temperature /Proc 1 Temp (#0x98)    	The BMC on S5000PSL has reported a warning assertion event for Proc 1 Temp.  The event has the following information: the Proc 1 Temp is in a high, but non-critical, and going higher state.  Sensor reading: 127.00  degrees C.  Threshold value: 99.00  degrees C.  Please check the device.                                                                                                              	BMC - LUN #0 (Channel #00h)                   

11  	10/10/2021-08:17:17  	Temperature /Proc 1 Temp (#0x98)    	The BMC on S5000PSL has reported a critical assertion event for Proc 1 Temp.  The event has the following information: the Proc 1 Temp is high, critical, and going higher state.  Sensor reading: 127.00  degrees C.  Threshold value: 108.00  degrees C.  Please check the device.                                                                                                                         	BMC - LUN #0 (Channel #00h)                   

12  	10/10/2021-08:17:31  	System Event #0x83                  	The BIOS on S5000PSL has reported an informational assertion event for System Event sensor 131.  The event has the following information: Timestamp Clock Sync. Event is first of the pair.  There is no recommended action defined for this event.                                                                                                                                                          	BIOS (Channel #00h)                           

13  	10/10/2021-08:17:31  	System Event #0x83                  	The BIOS on S5000PSL has reported an informational assertion event for System Event sensor 131.  The event has the following information: Timestamp Clock Sync. Event is second of the pair.  There is no recommended action defined for this event.                                                                                                                                                         	BIOS (Channel #00h)                           

14  	10/10/2021-08:19:37  	System Event #0x01                  	The SMI Handler on S5000PSL has reported an informational assertion event for System Event sensor 1.  The event has the following information: an OEM system boot event has occurred.  There is no recommended action defined for this event.                                                                                                                                                                	SMI Handler (Channel #00h)                    

15  	10/10/2021-08:20:34  	System ACPI Power State /SysACPIPowe	The BMC on S5000PSL has reported an informational assertion event for SysACPIPowerStat.  The event has the following information: S0/G0.  There is no recommended action defined for this event.                                                                                                                                                                                                             	BMC - LUN #0 (Channel #00h)                   

16  	10/10/2021-08:29:10  	Button /Button (#0x84)              	The BMC on S5000PSL has reported an informational assertion event for Button.  The event has the following information: the reset button has been pressed.  There is no recommended action defined for this event.                                                                                                                                                                                           	BMC - LUN #0 (Channel #00h)                   

17  	10/10/2021-08:29:12  	Temperature /Proc 1 Temp (#0x98)    	The BMC on S5000PSL has reported an informational deassertion event for Proc 1 Temp.  The event has the following information: the Proc 1 Temp is no longer in a high non-critical state.  Sensor reading: 127.00  degrees C.  Threshold value: 99.00  degrees C.  No action is required.                                                                                                                    	BMC - LUN #0 (Channel #00h)                   

18  	10/10/2021-08:29:12  	Temperature /Proc 1 Temp (#0x98)    	The BMC on S5000PSL has reported an informational deassertion event for Proc 1 Temp.  The event has the following information: the Proc 1 Temp is no longer in a critically high state.  Sensor reading: 127.00  degrees C.  Threshold value: 108.00  degrees C.  No action is required.                                                                                                                     	BMC - LUN #0 (Channel #00h)                   

19  	10/10/2021-08:29:13  	Temperature /Proc 1 Temp (#0x98)    	The BMC on S5000PSL has reported a warning assertion event for Proc 1 Temp.  The event has the following information: the Proc 1 Temp is in a high, but non-critical, and going higher state.  Sensor reading: 127.00  degrees C.  Threshold value: 99.00  degrees C.  Please check the device.                                                                                                              	BMC - LUN #0 (Channel #00h)                   

20  	10/10/2021-08:29:13  	Temperature /Proc 1 Temp (#0x98)    	The BMC on S5000PSL has reported a critical assertion event for Proc 1 Temp.  The event has the following information: the Proc 1 Temp is high, critical, and going higher state.  Sensor reading: 127.00  degrees C.  Threshold value: 108.00  degrees C.  Please check the device.                                                                                                                         	BMC - LUN #0 (Channel #00h)                   

21  	10/10/2021-08:29:42  	System Event #0x83                  	The BIOS on S5000PSL has reported an informational assertion event for System Event sensor 131.  The event has the following information: Timestamp Clock Sync. Event is first of the pair.  There is no recommended action defined for this event.                                                                                                                                                          	BIOS (Channel #00h)                           

22  	10/10/2021-08:29:42  	System Event #0x83                  	The BIOS on S5000PSL has reported an informational assertion event for System Event sensor 131.  The event has the following information: Timestamp Clock Sync. Event is second of the pair.  There is no recommended action defined for this event.                                                                                                                                                         	BIOS (Channel #00h)                           

23  	10/10/2021-08:31:56  	System Event #0x01                  	The SMI Handler on S5000PSL has reported an informational assertion event for System Event sensor 1.  The event has the following information: an OEM system boot event has occurred.  There is no recommended action defined for this event.                                                                                                                                                                	SMI Handler (Channel #00h)                    

24  	10/10/2021-08:32:53  	System ACPI Power State /SysACPIPowe	The BMC on S5000PSL has reported an informational assertion event for SysACPIPowerStat.  The event has the following information: S0/G0.  There is no recommended action defined for this event.                                                                                                                                                                                                             	BMC - LUN #0 (Channel #00h)                   

25  	10/10/2021-08:36:38  	Button /Button (#0x84)              	The BMC on S5000PSL has reported an informational assertion event for Button.  The event has the following information: the reset button has been pressed.  There is no recommended action defined for this event.                                                                                                                                                                                           	BMC - LUN #0 (Channel #00h)                   

26  	10/10/2021-08:36:40  	Temperature /Proc 1 Temp (#0x98)    	The BMC on S5000PSL has reported an informational deassertion event for Proc 1 Temp.  The event has the following information: the Proc 1 Temp is no longer in a high non-critical state.  Sensor reading: 127.00  degrees C.  Threshold value: 99.00  degrees C.  No action is required.                                                                                                                    	BMC - LUN #0 (Channel #00h)                   

27  	10/10/2021-08:36:40  	Temperature /Proc 1 Temp (#0x98)    	The BMC on S5000PSL has reported an informational deassertion event for Proc 1 Temp.  The event has the following information: the Proc 1 Temp is no longer in a critically high state.  Sensor reading: 127.00  degrees C.  Threshold value: 108.00  degrees C.  No action is required.                                                                                                                     	BMC - LUN #0 (Channel #00h)                   

28  	10/10/2021-08:36:40  	Temperature /Proc 1 Temp (#0x98)    	The BMC on S5000PSL has reported a warning assertion event for Proc 1 Temp.  The event has the following information: the Proc 1 Temp is in a high, but non-critical, and going higher state.  Sensor reading: 127.00  degrees C.  Threshold value: 99.00  degrees C.  Please check the device.                                                                                                              	BMC - LUN #0 (Channel #00h)                   

29  	10/10/2021-08:36:40  	Temperature /Proc 1 Temp (#0x98)    	The BMC on S5000PSL has reported a critical assertion event for Proc 1 Temp.  The event has the following information: the Proc 1 Temp is high, critical, and going higher state.  Sensor reading: 127.00  degrees C.  Threshold value: 108.00  degrees C.  Please check the device.                                                                                                                         	BMC - LUN #0 (Channel #00h)                   

30  	10/10/2021-08:37:10  	System Event #0x83                  	The BIOS on S5000PSL has reported an informational assertion event for System Event sensor 131.  The event has the following information: Timestamp Clock Sync. Event is first of the pair.  There is no recommended action defined for this event.                                                                                                                                                          	BIOS (Channel #00h)                           

31  	10/10/2021-08:37:10  	System Event #0x83                  	The BIOS on S5000PSL has reported an informational assertion event for System Event sensor 131.  The event has the following information: Timestamp Clock Sync. Event is second of the pair.  There is no recommended action defined for this event.                                                                                                                                                         	BIOS (Channel #00h)                           

32  	10/10/2021-08:38:59  	System Event #0x01                  	The SMI Handler on S5000PSL has reported an informational assertion event for System Event sensor 1.  The event has the following information: an OEM system boot event has occurred.  There is no recommended action defined for this event.                                                                                                                                                                	SMI Handler (Channel #00h)                    

33  	10/10/2021-08:39:53  	System ACPI Power State /SysACPIPowe	The BMC on S5000PSL has reported an informational assertion event for SysACPIPowerStat.  The event has the following information: S0/G0.  There is no recommended action defined for this event.                                                                                                                                                                                                             	BMC - LUN #0 (Channel #00h)                   

34  	10/10/2021-08:48:53  	Temperature /Proc 1 Temp (#0x98)    	The BMC on S5000PSL has reported an informational deassertion event for Proc 1 Temp.  The event has the following information: the Proc 1 Temp is no longer in a high non-critical state.  Sensor reading: 127.00  degrees C.  Threshold value: 99.00  degrees C.  No action is required.                                                                                                                    	BMC - LUN #0 (Channel #00h)                   

35  	10/10/2021-08:48:53  	Temperature /Proc 1 Temp (#0x98)    	The BMC on S5000PSL has reported an informational deassertion event for Proc 1 Temp.  The event has the following information: the Proc 1 Temp is no longer in a critically high state.  Sensor reading: 127.00  degrees C.  Threshold value: 108.00  degrees C.  No action is required.                                                                                                                     	BMC - LUN #0 (Channel #00h)                   

36  	10/10/2021-08:48:54  	Temperature /Proc 1 Temp (#0x98)    	The BMC on S5000PSL has reported a warning assertion event for Proc 1 Temp.  The event has the following information: the Proc 1 Temp is in a high, but non-critical, and going higher state.  Sensor reading: 127.00  degrees C.  Threshold value: 99.00  degrees C.  Please check the device.                                                                                                              	BMC - LUN #0 (Channel #00h)                   

37  	10/10/2021-08:48:54  	Temperature /Proc 1 Temp (#0x98)    	The BMC on S5000PSL has reported a critical assertion event for Proc 1 Temp.  The event has the following information: the Proc 1 Temp is high, critical, and going higher state.  Sensor reading: 127.00  degrees C.  Threshold value: 108.00  degrees C.  Please check the device.                                                                                                                         	BMC - LUN #0 (Channel #00h)                   

38  	10/10/2021-08:49:23  	System Event #0x83                  	The BIOS on S5000PSL has reported an informational assertion event for System Event sensor 131.  The event has the following information: Timestamp Clock Sync. Event is first of the pair.  There is no recommended action defined for this event.                                                                                                                                                          	BIOS (Channel #00h)                           

39  	10/10/2021-08:49:23  	System Event #0x83                  	The BIOS on S5000PSL has reported an informational assertion event for System Event sensor 131.  The event has the following information: Timestamp Clock Sync. Event is second of the pair.  There is no recommended action defined for this event.                                                                                                                                                         	BIOS (Channel #00h)                           

40  	10/10/2021-08:50:43  	Temperature /Proc 1 Temp (#0x98)    	The BMC on S5000PSL has reported an informational deassertion event for Proc 1 Temp.  The event has the following information: the Proc 1 Temp is no longer in a high non-critical state.  Sensor reading: 127.00  degrees C.  Threshold value: 99.00  degrees C.  No action is required.                                                                                                                    	BMC - LUN #0 (Channel #00h)                   

41  	10/10/2021-08:50:43  	Temperature /Proc 1 Temp (#0x98)    	The BMC on S5000PSL has reported an informational deassertion event for Proc 1 Temp.  The event has the following information: the Proc 1 Temp is no longer in a critically high state.  Sensor reading: 127.00  degrees C.  Threshold value: 108.00  degrees C.  No action is required.                                                                                                                     	BMC - LUN #0 (Channel #00h)                   

42  	10/10/2021-08:50:44  	Temperature /Proc 1 Temp (#0x98)    	The BMC on S5000PSL has reported a warning assertion event for Proc 1 Temp.  The event has the following information: the Proc 1 Temp is in a high, but non-critical, and going higher state.  Sensor reading: 127.00  degrees C.  Threshold value: 99.00  degrees C.  Please check the device.                                                                                                              	BMC - LUN #0 (Channel #00h)                   

43  	10/10/2021-08:50:44  	Temperature /Proc 1 Temp (#0x98)    	The BMC on S5000PSL has reported a critical assertion event for Proc 1 Temp.  The event has the following information: the Proc 1 Temp is high, critical, and going higher state.  Sensor reading: 127.00  degrees C.  Threshold value: 108.00  degrees C.  Please check the device.                                                                                                                         	BMC - LUN #0 (Channel #00h)                   

44  	10/10/2021-08:50:58  	System Event #0x83                  	The BIOS on S5000PSL has reported an informational assertion event for System Event sensor 131.  The event has the following information: Timestamp Clock Sync. Event is first of the pair.  There is no recommended action defined for this event.                                                                                                                                                          	BIOS (Channel #00h)                           

45  	10/10/2021-08:50:58  	System Event #0x83                  	The BIOS on S5000PSL has reported an informational assertion event for System Event sensor 131.  The event has the following information: Timestamp Clock Sync. Event is second of the pair.  There is no recommended action defined for this event.                                                                                                                                                         	BIOS (Channel #00h)                           

46  	10/10/2021-08:53:00  	System Event #0x01                  	The SMI Handler on S5000PSL has reported an informational assertion event for System Event sensor 1.  The event has the following information: an OEM system boot event has occurred.  There is no recommended action defined for this event.                                                                                                                                                                	SMI Handler (Channel #00h)
0
1355 / 490 / 95
Регистрация: 11.03.2015
Сообщений: 1,678
12.10.2021, 15:48 3
lertroll,
Перешивать надо, всё полностью, особенно не забыть FRU (Field Replaceable Units)/SDR(Sensor Data Records), они вот за это и отвечают.
1
0 / 0 / 0
Регистрация: 10.10.2021
Сообщений: 3
16.10.2021, 21:39  [ТС] 4
Спасибо, это помогло.
0
IT_Exp
Эксперт
87844 / 49110 / 22898
Регистрация: 17.06.2006
Сообщений: 92,604
16.10.2021, 21:39

ESXi 5.x на материнской плате Intel DP35DP
Получил материнскую плату(Intel E210882 AA-D81073 775 сокет), проц.(Core 2 Duo E6850), оперативка...

После замены Wifi модуля Broadcom на Intel advanced-N 6205 не могу настроить сеть
Имею ноут бук Sony Vaio SVF1521M1RW ОС : Windows 8.1 В нём была установлена плата wi-fi...

Вывести файл до замены и после замены.
Нужно что бы было видно файл до замены и после замены. Program fail; uses crt; var f:text; ct:...

Отключение алертов на службы с рандомными именами в Zabbix
Коллеги, добрый день. Есть на windows server такие службы как OneSyncSvc,...

имеет ли смысл замены Celeron 430,1800MHz(9X200) на Intel Pentium D 2,80GHz?
Добрый вечер всем!!Перейду сразу к вопросу,у меня стоит процессор Intei Celeron 430,1800MHz(9X200)...

Monitoring Configuration - где настраивается адрес для алертов?
Коллеги, подскажите, где настраивается адрес для проб и алертов ddm? --- Добавлено 24 янв...


Искать еще темы с ответами

Или воспользуйтесь поиском по форуму:
4
Ответ Создать тему
Опции темы

КиберФорум - форум программистов, компьютерный форум, программирование
Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2021, vBulletin Solutions, Inc.