Проект "Говорящий будильник"

#if _USE_IOCTL == 1
DRESULT USER_ioctl (
    BYTE pdrv,      /* Physical drive nmuber (0..) */
    BYTE cmd,       /* Control code */
    void *buff      /* Buffer to send/receive control data */
)
{
  /* USER CODE BEGIN IOCTL */
    DRESULT res;
    
    HAL_UART_Transmit(&huart2,(uint8_t*)"USER_ioctl\r\n",12,0x1000); 
    sprintf(str1,"cmd: %d\r\n",cmd); 
    HAL_UART_Transmit(&huart2,(uint8_t*)str1,strlen(str1),0x1000); 
    
    if (pdrv) return RES_PARERR; 
    if (Stat & STA_NOINIT) return RES_NOTRDY; 
    res = RES_ERROR; 
    switch (cmd){ 
        case GET_SECTOR_SIZE : /* Get sectors on the disk (WORD) */ 
            *(WORD*)buff = 512; 
            res = RES_OK; 
        break;
        case GET_SECTOR_COUNT :
            *(DWORD*)buff = 4194304;
            res = RES_OK;
        break;
        case GET_BLOCK_SIZE :
            *(DWORD*)buff = 1;
            res = RES_OK;
        break;
        case CTRL_SYNC:
            SS_SD_SELECT(); 
            if (SPI_wait_ready() == 0xFF) 
                res = RES_OK; 
        break;
        default: 
            res = RES_PARERR; 
    } 
    SPI_Release(); 
    
    return res;
  /* USER CODE END IOCTL */
}
#endif /* _USE_IOCTL == 1 */

DWORD plist[] = {100, 0, 0, 0};
PARTITION VolToPart[]={
    {0,1}
};
BYTE work[_MAX_SS];
 
int main(void)
{
  /* USER CODE BEGIN 1 */
  //uint16_t i; 
  //FRESULT res; //rezultat wypolneniya 
  uint8_t wtext1[]="Hello from STM32 !!! Writing and into time reading file works perfectly, but is not read from Windows 10";
  //FILINFO fileInfo; 
  //char *fn; 
  //DIR dir; 
  //DWORD fre_clust, fre_sect, tot_sect; 
  /* USER CODE END 1 */
 
  /* MCU Configuration----------------------------------------------------------*/
 
  /* Reset of all peripherals, Initializes the Flash interface and the Systick. */
  HAL_Init();
 
  /* USER CODE BEGIN Init */
 
  /* USER CODE END Init */
 
  /* Configure the system clock */
  SystemClock_Config();
 
  /* USER CODE BEGIN SysInit */
 
  /* USER CODE END SysInit */
 
  /* Initialize all configured peripherals */
  MX_GPIO_Init();
  MX_USART2_UART_Init();
  MX_TIM2_Init();
  MX_FATFS_Init();
  MX_SPI2_Init();
  /* USER CODE BEGIN 2 */
  HAL_TIM_Base_Start_IT(&htim2); 
  //SD_PowerOn(); 
  //sd_ini();
  //SD_Write_Block((uint8_t*)buffer1,0x0400); //zapishem block w bufer
  //SD_Read_Block(sect,0x0400); //schitaem block iz bufera
  //for(i=0;i<512;i++) HAL_UART_Transmit(&huart2,sect+i,1,0x1000);
  //HAL_UART_Transmit(&huart2,(uint8_t*)"\r\n",2,0x1000); 
  disk_initialize(SDFatFs.drv);
  
    //format
    if(f_fdisk(0, plist, work)!=FR_OK){
        Error();
    }else{
        if( f_mount(&SDFatFs, "0:", 1)!=FR_OK){
            Error();
        }else{
            if( f_mkfs(USER_Path, 0, 512) != FR_OK) {
                 Error();
            }
        }
    }
 
    /* Infinite loop */
  /* USER CODE BEGIN WHILE */
  while (1)
  {
 
  /* USER CODE END WHILE */
 
  /* USER CODE BEGIN 3 */
     
  }
  /* USER CODE END 3 */
 
}

char USER_Path[4]={0}; /* logical drive path */ 
FATFS SDFatFs;